Alexander
Stretching
Sharing a little side project with everyone.
Bit of backstory relating to this.
My dogs, as they tend to do, are getting older and all that comes with that. Been seeing a lot lately social media lately talking about how standard dog watering bowls and feeding bowls are very substandard (typically made out of not food grade stainless steel, and tend to quickly develop a bio film (that slimy stuff that tends to stick to the side of them after a day or two))
mmmmkay... well darn, i sure wouldn't like to drink out of a cup with slimy walls.
Of course all the info came at the price of learning that I could buy a food grade stainless, dog watering fountain that kept dog water clean and fresh, for the low low price of way to much dinero.
Being the Frugal person I am... I started humming the tune to "There's gotta be a better way"
and here ya go, A cheap DIY automatic Dog watering bowl, Which uses a purpose built trash product actively designed to store water in a clean condition long term.
Made out of Flash Heat molded Polycarbonate a standard 5 gallon office water jug (use the polycarbonate version, not the slightly different one with the dark blue handle)
The flash heat molded polycarbonate has an ultra smooth interior surface that biofilm has great difficulty in sticking to.

I had already dont some cutting and fitting... but this is what you want to start with... standard water cooler jug

use a hole saw to cut a hole at the indicated point, use a grinder with a cutting wheel to cut the top off the bottle as shown.

Item # 1 is a standard 1 inch Uniseal, typically used in hydrosystems to provide a watertight bulkhead.
Item # 2 is a piece of PVC pipe pushed thru the Uniseal (might want to let the uniseal sit in hot water for a minute, and add a little olive oil or coconut oil to help seat the pvc in place.
Item # 3 shows that the PVC should go far enough thru to sit flush with top edge of the piece (the top edge will be where you cut bottle in half) Leave a couple inches of slack on the other side

Here it is assembled, Pump in the bottom, Top half of jug inverted, the black line around the edge is rubber floor edging to provide a strong grip so that the top wont slide around or shift. power cord for the pump run out of the hole in the back of the jug.
Final Steps

Item #1 drill 4 holes around the PVC pipe as show, make sure that the are of large enough diameter to easily allow quick water return down the pipe to the resevoir.
Item #2 run PVC line from like the large air tubing from the pump up thru the pvc and out the side I used a T junction inside the pipe and capped the top of the T with hot glue.
Pump size, the one shown in these picture ended up being far to large and loud for this project. Although not shown in the pictures the one that I have in it now is perfect. A very small design, typically used in small outdoor water fountains. you want something along the lines of 80-100 GPH typically run less than ten bucks each on amazon. Just make sure it has a lift height of at least 3 feet.
I chose to Paint the outside for the purpose of keeping light out of the water, Honestly you could certainly leave it clear.
Voila... you got yourself a self watering dog fountain, You can put the pump on a timer switch (it really doesn't need to run constantly)
It has approximately 3 1/2 gallons of storage capacity in the res, holds probably half a gallon more in the bowl uptop, Keeps and slimy icky stuff from growing, recirculates the water to keep it fresh and oxygenated. and the cherries on the top, it Makes use of an item that would otherwise just end up in a landfill, while simultaneously costing a tiny fraction of the commercial equivalent (which has a much lower capacity)
All 4 of our dogs took to it almost immediately (they were a bit hesitant the first day, as i was still using the larger 250 gallon pump and that hummed way to loudly)
We went from needing to refill dog bowls twice daily, to now its once every 2-3 days. Filling it is super easy, just pour water in at the top. As long as you dont pour it to fast it quickly rushes back down to the res via the 4 holes you put in the PVC pipe. Cleaning is a breeze, simply disconnect your feed line, lift up the top (keep it level) then dump all the water, clean wipe it down, refill and continue with ya life. I have been doing that about once a week, water is still quite nice, but there tends to be some hair, and other gunk that gets in dog bowls.
Bit of backstory relating to this.
My dogs, as they tend to do, are getting older and all that comes with that. Been seeing a lot lately social media lately talking about how standard dog watering bowls and feeding bowls are very substandard (typically made out of not food grade stainless steel, and tend to quickly develop a bio film (that slimy stuff that tends to stick to the side of them after a day or two))
mmmmkay... well darn, i sure wouldn't like to drink out of a cup with slimy walls.
Of course all the info came at the price of learning that I could buy a food grade stainless, dog watering fountain that kept dog water clean and fresh, for the low low price of way to much dinero.
Being the Frugal person I am... I started humming the tune to "There's gotta be a better way"
and here ya go, A cheap DIY automatic Dog watering bowl, Which uses a purpose built trash product actively designed to store water in a clean condition long term.
Made out of Flash Heat molded Polycarbonate a standard 5 gallon office water jug (use the polycarbonate version, not the slightly different one with the dark blue handle)
The flash heat molded polycarbonate has an ultra smooth interior surface that biofilm has great difficulty in sticking to.

I had already dont some cutting and fitting... but this is what you want to start with... standard water cooler jug

use a hole saw to cut a hole at the indicated point, use a grinder with a cutting wheel to cut the top off the bottle as shown.

Item # 1 is a standard 1 inch Uniseal, typically used in hydrosystems to provide a watertight bulkhead.
Item # 2 is a piece of PVC pipe pushed thru the Uniseal (might want to let the uniseal sit in hot water for a minute, and add a little olive oil or coconut oil to help seat the pvc in place.
Item # 3 shows that the PVC should go far enough thru to sit flush with top edge of the piece (the top edge will be where you cut bottle in half) Leave a couple inches of slack on the other side

Here it is assembled, Pump in the bottom, Top half of jug inverted, the black line around the edge is rubber floor edging to provide a strong grip so that the top wont slide around or shift. power cord for the pump run out of the hole in the back of the jug.
Final Steps

Item #1 drill 4 holes around the PVC pipe as show, make sure that the are of large enough diameter to easily allow quick water return down the pipe to the resevoir.
Item #2 run PVC line from like the large air tubing from the pump up thru the pvc and out the side I used a T junction inside the pipe and capped the top of the T with hot glue.
Pump size, the one shown in these picture ended up being far to large and loud for this project. Although not shown in the pictures the one that I have in it now is perfect. A very small design, typically used in small outdoor water fountains. you want something along the lines of 80-100 GPH typically run less than ten bucks each on amazon. Just make sure it has a lift height of at least 3 feet.
I chose to Paint the outside for the purpose of keeping light out of the water, Honestly you could certainly leave it clear.
Voila... you got yourself a self watering dog fountain, You can put the pump on a timer switch (it really doesn't need to run constantly)
It has approximately 3 1/2 gallons of storage capacity in the res, holds probably half a gallon more in the bowl uptop, Keeps and slimy icky stuff from growing, recirculates the water to keep it fresh and oxygenated. and the cherries on the top, it Makes use of an item that would otherwise just end up in a landfill, while simultaneously costing a tiny fraction of the commercial equivalent (which has a much lower capacity)
All 4 of our dogs took to it almost immediately (they were a bit hesitant the first day, as i was still using the larger 250 gallon pump and that hummed way to loudly)
We went from needing to refill dog bowls twice daily, to now its once every 2-3 days. Filling it is super easy, just pour water in at the top. As long as you dont pour it to fast it quickly rushes back down to the res via the 4 holes you put in the PVC pipe. Cleaning is a breeze, simply disconnect your feed line, lift up the top (keep it level) then dump all the water, clean wipe it down, refill and continue with ya life. I have been doing that about once a week, water is still quite nice, but there tends to be some hair, and other gunk that gets in dog bowls.