Nothing Fancy

Caddis · May 21, 2020

The auto fill vaporizer is going to need a tweak.
I knew it was not vented when venting drained the tank.

After getting the fitting, I proceeded to fill the tank, POP, cracked the tank.
Some time of pressure relief valve is needed?
This happens sometimes when you throw stuff at the wall.
Me-?
Wall- Way ahead ?

NotAquaMan · May 21, 2020

Caddis said:
The auto fill vaporizer is going to need a tweak.
I knew it was not vented when venting drained the tank.
After getting the fitting, I proceeded to fill the tank, POP, cracked the tank.
Some time of pressure relief valve is needed?
This happens sometimes when you throw stuff at the wall.
Me-?
Wall- Way ahead ? View attachment 11518

You will get it sorted bro that I'm certain. Shitty it happened but gives ya something to do ?

Caddis · May 21, 2020

Things are looking better, did some rearranging, some on probation.
Between keeping the temp/ humidity somewhat in sync and dropping the ph down, seems to be working.
I made these work harder than they needed to, hindsight, should have top feed more initially

Ghost Town & C&C

GT, C&C, Atonic/Apollo 13 and Monkey Juice (F)

BOO (F) & Atonic x Apollo 13 F4 (F?)

Panama V2, Gogi OGx CD (2) & Putang.

Crippy’s, C&C and GT

Caddis · May 21, 2020

The one Crippy is my fault, but look at this goober?

Almost need to know what’s going to be?

NotAquaMan · May 21, 2020

They looking really nice bro. Now ya getting it dialed in.

Caddis · May 21, 2020

NotAquaMan said:
You will get it sorted bro that I'm certain. Shitty it happened but gives ya something to do ?

At this point, I’m only filling once a day.
I may check into a replacement tank or FlexSeal it! )
What kind of valve would allow venting like this?

Caddis · May 21, 2020

NotAquaMan said:
They looking really nice bro. Now ya getting it dialed in.

NotAquaMan · May 21, 2020

Caddis said:
At this point, I’m only filling once a day.
I may check into a replacement tank or FlexSeal it! )
What kind of valve would allow venting like this?

One way check valve for like aquarium air lines.

Amazon product

NotAquaMan · May 21, 2020

Caddis said:

One of my most favorite of all time bro

Caddis · May 21, 2020

The GP is filling in nicely, kinda wish it wasn’t a vert., i might have scorched it a touch.

I was looking for papers yesterday and found a white paper gift sack, my DCSE order of MM stuff.
Reminded me of Deebs thread on finding a stash.
Extra was Mexican Peanutbutter!

Caddis · May 21, 2020

NotAquaMan said:
One way check valve for like aquarium air lines.

Amazon product

Need a sealed penetration to run a line with that attached?
A uniseal?

NotAquaMan · May 21, 2020

Caddis said:
Need a sealed penetration to run a line with that attached?
A uniseal?

I would just drill like a 1/8 hole and epoxy it in. Just make sure facing the right way

Caddis · May 21, 2020

NotAquaMan said:
I would just drill like a 1/8 hole and epoxy it in. Just make sure facing the right way

So glue straight in the hole, cool!
Any of these work under water, cuz I got a hole like that! ?

NotAquaMan · May 21, 2020

Caddis said:
So glue straight in the hole, cool!

Yup about the cheapest pressure relief valve you can get lol. Like $1 each. Should be close to about 5-10lb. There are better quality ones if ya like but the cheapies work. Can also out 2 in to be safe

Caddis · May 24, 2020

Death, carnage and rebirth have been experienced in the last couple days.

Initially, I had a plan to run specific strains, but after posting for the first time ever, I got caught up in stuff.
I was trying to fuck things up, so reboot.

Put the big cloner together and went to grab‘in and slashing anything not nailed down.

Pretty much blasting them continuous
I’ve looked at the Turbocloner? with the fan. Supposed to keep the heat down.
After seeing Spy’s fogger parts list, I ordered the fan to try, thinking duct out a lid penetration? Not sure how to rig it on the side?

The f & d with the Berry Nice seedlings and misc. H clones moved for the cloner.

Front right is a seed start C&C I decided to spare, for now. Sex?

I took the GP down and moved the light for these.
I really don’t like solo bucket dwc and that was taking up space and a pain working around the light.

I’ve never really tested this for a full run. The first spray tips were not very good, these are ez cloner tips.
I know the pond fogger didn’t work, too much area?

spyralout · May 24, 2020

Caddis said:
Mexican Peanutbutter!

Caddis said:
I ordered the fan to try, thinking duct out a lid penetration? Not sure how to rig it on the side?

My first time on this too, it's been working great so far, just a few adjustments I can see for my situation. It's almost like I'm cooling down fuel lines to atomize the gas better for the carb and intake. I think one of the keys is that your exhaust ports (delivering the fog) need to be more than the intake fan. Hence the dual exhaust. If you had the tote inside the grow space, then no need for hoses, and you can probably get away with one bigass exhaust hole. Having the tote (or whatever vessel) inside the grow space would produce a shit ton of fog in a matter of minutes, harder to control, cumbersome to fill, and use up valuable grow space. Plus you'd need to lightproof your vessel more or risk algae. I typically save the side port stuff for times that I really need to. The vessel itself is best if it remains as unmodified "hole wise" as possible IMO. That's why I prefer to mess with the lid. If you need to do it for plumbing config reasons, maybe use a barb fitting or a bulkhead? I couldn't find any ducting smaller than 4" and radiator hose was hard to bend (and expensive!). So I came up with the sump hose route.

Pic above ^ man that's really blasting the shit out of em, my oldskool EZ-Cloner had a fraction of that spray, but maybe cuz it's old. It works though.

Caddis · May 24, 2020

Welp, the dust has settled and I have the uc headin in the right direction now.

Panama V2, second seed run.

BOO, second seed run

Putang, she’s had a tough start, on me.

Monkey Juice, been running the extras, need to get to the meat! )

I can say from real world results, these 288 4K qb’s will hold them down, one 1” node spacing on almost everything that was going. That Panama would be out of control at this stage, keeping with the neighbors.
I may just run the boards and strips in veg?

Topping off the rez, I love how clean this is, use to have to clean the residue every time.

Caddis · May 24, 2020

spyralout said:
View attachment 11959

My first time on this too, it's been working great so far, just a few adjustments I can see for my situation. It's almost like I'm cooling down fuel lines to atomize the gas better for the carb and intake. I think one of the keys is that your exhaust ports (delivering the fog) need to be more than the intake fan. Hence the dual exhaust. If you had the tote inside the grow space, then no need for hoses, and you can probably get away with one bigass exhaust hole. Having the tote (or whatever vessel) inside the grow space would produce a shit ton of fog in a matter of minutes, harder to control, cumbersome to fill, and use up valuable grow space. Plus you'd need to lightproof your vessel more or risk algae. I typically save the side port stuff for times that I really need to. The vessel itself is best if it remains as unmodified "hole wise" as possible IMO. That's why I prefer to mess with the lid. If you need to do it for plumbing config reasons, maybe use a barb fitting or a bulkhead? I couldn't find any ducting smaller than 4" and radiator hose was hard to bend (and expensive!). So I came up with the sump hose route.

Pic above ^ man that's really blasting the shit out of em, my oldskool EZ-Cloner had a fraction of that spray, but maybe cuz it's old. It works though.

You don’t know how hard it was not to spill water on a couple of those!

spyralout · May 24, 2020

Caddis said:
out of control at this stage,

I think I'm running into this issue right about now lol

Caddis said:
Topping off the rez, I love how clean this is, use to have to clean the residue every time.

What is that blue thing?

Do you ever get that "wet rag left in the washing machine" or "old sponge in the sink mildew" smell on the edges of the res tote? Especially if the lid is on and water condensates along those edges.

I like this one:

Caddis · May 24, 2020

That blue thing is the cheapest pump I ever bought, bottom draw does a good job.
I have it on a seconds timer, few seconds every hour. The airstone doesn’t do as well for me. Don’t need the aeration at this stage.

I don’t get any smells like that, your running MC?
I check my stuff by smell all the time. I may not be very scientific, but I’m hands on.

I don’t know if Jack’s grows better but I really like how clean it runs for me.

Nothing Fancy

Zinger

In Bloom

Zinger

Zinger

Attachments

In Bloom

Zinger

Zinger

In Bloom

In Bloom

Zinger

Zinger

In Bloom

Zinger

In Bloom

Zinger

🌱🌿🌲🔥💨

Zinger

Attachments

Zinger

🌱🌿🌲🔥💨

Zinger

Similar threads